にほんブログ村 IT技術ブログへ
にほんブログ村

Linux ブログランキングへ

2016年07月04日

Ubuntu改造日記 Windows10用Bai-Trail世代中華タブレット Win-70B Ubuntu16.04インストールテスト編 その36

CmceA-qVUAEajKy.jpg

今日は前回の続きでBay-Trail世代のWindows10中華タブレットで
Ubuntuをインストールして動かしてみました。
前回のほぼコピペです。

Ubuntu16.04の登場で標準のKernelが対応増えてかなり楽になりました。
Ubuntuも旧機種であればそれなりにちゃんと動きます。
OSC名古屋2016で色々と質問を頂いたので
ARM主体の生活ですが買って試してみました。

●Bay-Trail世代中華タブレットとUbuntu16.04
Windows10タブレットがブームになったのが、
恐らくこのBay-Trail世代かと思います。
2014年から色々と語られ続けてきましたが、
Kernelの対応が遅れ、ドライバとUEFI32bitで悲しい思いを
してきたはずかと思います。
Ubuntu16.04世代ではちゃんと動くと良いですね。

前回Wubi for Ubuntu16.04が何のトラブルもなく動いたので
今回のテスト機を購入しました。

・KEIAN WIN-70b
・OS:Windows 10 Home 32bit
・CPU:Intel Bay Trail Z3735G 1.33GHz, 4C/4T CPU
・GPU:Intel HD Graphic(Gen7)
・メモリ:DDR3-L DRAM 1GB
・ストレージ:16GB
・ディスプレイ:7インチIPS 解像度1024 x 600
・タッチパネル:5 ポイントマルチタッチ
・カメラ:インカメラ 0.3M Pixel
・スピーカー:8Ω/0.8W スピーカー x 1
・インターフェイス:Mini HDMI x 1
   Micro USB 2.0 x1
   Micro SD slot(最大32GB) x1
   3.5mm オーディオジャック x 1,
・無線LAN:IEEE Wi-Fi 802.11 b/g/n
・Bluetooth:Bluetooth 4.0
・本体サイズ:188.5×108.5×8.5mm
・本体重量:約271g
・バッテリ / パワー:2600 mAh / 3.7 V / Li-Polymer 、 5V 1.5A
・発売日 2015年9月



秋葉原の某2F PCジャンクショップでOSなし品を
5980円で購入しました。
これUbuntu起動しなかったら完全にNG。
初心者は絶対手を出してはいけません。
格安中華タブレットです。

ですが、こいつネットで調べると結構大変で、
Linux使い泣かせの設計しています。
まあ2台目なので、慣れればなんとか。1回目地獄
今回は情報ありなので途中まで。
今回は大体殆どこちらのサイト様を参考させていただきました。
大変感謝です。

 Windows tabletに遊ばれてみた part1 -- NEC TW708/basにubuntuを入れる。


●UEFI32bitとUbuntu16.04 64bitをインストール
Bay-Trail世代のCPUは64bit版なので、
当然Ubuntu16.04も64bit版が必要です。

ただし、Bay-Trail世代はUEFIが32bitなので
ブートローダー(Grub2)がそのまま入らない設計ですw
実はLinuxではUEFI32bitは標準対応は外してありますw
なので、通常のUbuntuを使うと32bit版は全て32bit、
64bit版は全て64bitを使う必要があるのですが途中で止まりますw

・ハード 64bit⇒Ubuntu 64bit⇒UEFI 64bit⇒ブートローダー64bit
なら仮に標準でも何の問題もありません。
ただ実際は、

・ハード 64bit⇒Ubuntu 64bit⇒UEFI 32bit⇒ブートローダー64bit(NG)
となってしまい、Grub2を32bit版を後から入れる必要がありますw
つまりインストーラーが途中で落ちますw
面倒な設計ぢゃ

●あると便利なハード
・MicroUSB-USB変換コネクタ
・USBメモリ >2GB
・USBハブ
・USBキーボード
・USB無線LAN
・USBマウス

●USB-ISOイメージからUbuntu16.04 64bitをインストール
まず、Ubuntu16.04の64bit版ISOをダウンロードしてきて
USBメモリに焼きます。
その際に/EFI/BOOT/にUEFI32をコピーして有効化します。
ここに書いてある様に

 Mouse Computerのスティック型PC m-Stick MS-NH1にUbuntuをインストールする。

https://github.com/jfwells/linux-asus-t100ta/blob/master/boot/bootia32.efi
のbootia32.efiをダウンロードして、
USBメモリのUbuntuのEFI/BOOT/にコピーして保存します。
これでUEFI32bit機でUbuntuがブート出来る様になります。
分かれば簡単ですが、そこにたどり着くまでの苦労が忍ばれます。

次にMicroUSBにUSB変換ケーブルとハブ、キーボードとメモリを刺します。
他のハードも空いていれば繋ぎます。

電源ボタンをONにしたら速やかに「DEL」キーを押して
UEFI設定画面を出します。BIOSと同じですね。
機種によってボタンは変わりますのでググるしか。
実はOSがWindows10であろうと無かろうと同じだったりします。

まずセキュアブートをOFFにします。
次にUEFIの起動順番をUSB Ubuntuと書いてあるメモリを先頭にします。
で一旦Save &リセット。
これでUSBから起動出来るはずですが、こいつの場合はNGです。
参考サイト様に書いてありますが、

 EFIメニューのboot overrideからubuntuインストーラを起動

させる必要があります。
つまりUbuntuを起動させる為に毎回UEFIの画面を出してBoot overrideから起動w
面倒。
でもそれだけだったり・・・
これに気づくか気づかないかと言われると間違いなく気づかない。
先達様に大変感謝です。

Grub2が起動するはずなので、

 *Try Ubuntu without installing
 Install Ubuntu
 OEM install (for manufacturers)
 Check disc for defects

Install Ubuntuを選択します。
動作確認はTryの方で。
しかしこの機種はnomodesetをオプションに追加が必要です。
起動前に、「e」キーを押して編集します。
linux 〜 quiet
の行にquietの前にnomodesetを入力して「F10」キー
毎回入力が必要です。
多分ここまでやればBootします。

Ubuntuのインストーラーが立ち上がりましたら、
パーティションを分けて設定。
と言いたい所ですが、Windows10入っていないので全削除
Windows10込みの場合は無理そう。

 以下のデバイスのパーティションテーブルが変更されます:
 MMC/SDカード1(mmcblk0)

 以下のパーティションは初期化されます:
 MMC/SDカード1(mmcblk0)のパーティション2をext4に
 MMC/SDカード1(mmcblk0)のパーティション3をスワップに

通常ですとmmcblk02のパーティションにインストールされるはずです。
要注意なので覚えておきましょう。

日本語やキーボード、時間設定の所を通過してインストール開始しますと
ブートローダーの設定でエラーが出ます。
これは先ほど書きましたUEFI64Bit用のGrub2をインストールしようとして
エラーが出たとの事で、必ずエラーになります。
クリックして飛ばしますと無事Ubuntuが起動します。
まだUSB無線LANやネットやapt-getは使えません。

ここで再起動
再びUEFI画面からUSB-UbuntuをBoot overrideから起動
しつこいですが、この機種はUEFIでBoot overrideを選択しないとUbuntuは起動しません。
また同じ様にGrub2画面がでたら今度は「C」キーを押して
手動でGrub2から設定します。

 GNU GRUB version xxx
 〜

 grub>

と出たらコマンドをて入力。Tabキーで補完入力しましょう。
直接パーティションとKernelをCUIで指定してUbuntuを起動させます。
改行は普通にエンターキーです。
 
 grub> linux (hd1,gpt5)/boot/vmlinuz-4.4.0-21-generic root=/dev/mmcblk0p2 nomodeset reboot=pci 改行
 grub> initrd (hd1,gpt5)/boot/initrd-4.4.0-21-generic 改行
 grub> boot 改行

ここまで一通り出来ていればUbuntuが起動するはず。
端末画面とネットを繋げて確認しましょう。
Grub2-ia32をインストールします。

 sudo apt-get install grub-efi-ia32

念のためbootia32.efiをコピー

 sudo su
 sudo cp /media/removable/boot/EFI/bootia32.efi /boor/efi/EFI/

Grub2にnomodesetの設定

 sudo gedit /etc/defalut/grub

として10行目に
 GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"があります、その下に
 GRUB_CMDLINE_LINUX_DEFAULT='nomodeset'を追加し保存

次にGrub2の設定。

 sudo update-grub

昔はソースコードからビルドして作ったそうですが、
Ubuntu16.04ではその必要性はありません。
やっと再起動。
電源がおちたら再び「DEL」(以下略
ブートローダーにUbuntuと表示され、
Grub2が立ち上がってUbuntuが起動するはずです。

●疑わしい点
起動しない場合は
まず、

・UEFI32bit⇒Boot overrideを選択
・Grub2 32bit⇒手動でインストール

・/boot/efi/EFI/bootia32.efiが無い
 ⇒sudo suでスーパーユーザーになってcpしましょう

この3点が怪しいです。
一度確認してみましょう。

●Wifiとbluetoothドライバ
参考サイトを見ると、

 Wifi:rtl8188bs

だそうな。
githubにドライバソースコードがありますので、
make, sudo make install するだけです。

 sudo apt install build-esential linux-generic git-cvs
 git clone https://github.com/lwfinger/rtl8188bs.git

後はどちらもmake, sudo make installするだけです。

 cp /rtl8723bs
 make
 sudo make install

ビルドしたら再起動

●まとめ
内容は殆ど前回のコピペです。
一応なんとかUbuntuが起動するはずです。
元のOSがWindows10であろうと無かろうと
UEFI32bitの設定すればLinuxは起動します。
慣れたら色々なディストリを入れてみましょう。

過去のネット情報を調べると、Kernelが対応していないので
ビルドし直す必要がありそうですが、
Ubuntu16.04は直った後のKernelバージョンですw
大変便利になりました。
そういう意味ではUbuntuは便利です。
ただ周辺機種が動くかどうかで、まだ動かないものが沢山あります。
参考サイト様を確認して自分で設定するしかなさそうです。

そう言う意味ではLinuxをWindowsタブレットに入れる場合は
少しでも古い機種の方が対応されていて便利です。
特にWindows7世代はほぼフルオートで楽です。
でも先達の工夫で現在は手順を守れば簡単にUbuntu16.04が使えます。
大変便利になりました。
是非遊んでみましょう。


●PS
 WIN-70bのdmesgを公開します。
 こんな感じです。

 http://kapper1224.sakura.ne.jp/dmesg_WIN70b.log

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.0-21-generic (buildd@lgw01-21) (gcc version 5.3.1 20160413 (Ubuntu 5.3.1-14ubuntu2) ) #37-Ubuntu SMP Mon Apr 18 18:33:37 UTC 2016 (Ubuntu 4.4.0-21.37-generic 4.4.6)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.4.0-21-generic.efi.signed root=UUID=d3cf0412-63bf-4f90-b32b-8797e9e37b26 ro nomodeset
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] x86/fpu: Legacy x87 FPU detected.
[ 0.000000] x86/fpu: Using 'lazy' FPU context switches.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009dfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003bd3efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000003bd3f000-0x000000003bd6efff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000003bd6f000-0x000000003bda6fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000003bda7000-0x000000003c366fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000003c367000-0x000000003c5d0fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000003c5d1000-0x000000003c62afff] type 20
[ 0.000000] BIOS-e820: [mem 0x000000003c62b000-0x000000003cbfffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.31 by American Megatrends
[ 0.000000] efi: ACPI=0x3bda6000 ACPI 2.0=0x3bda6014 ESRT=0x3bd6e000 SMBIOS=0x3c5d0290
[ 0.000000] efi: requested map not found.
[ 0.000000] esrt: ESRT header is not in the memory map.
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: KEIAN Corporation WIN-70B/WIN-70B, BIOS 5.6.5 08/24/2015
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x3cc00 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 03E000000 mask FFE000000 uncachable
[ 0.000000] 2 base 03D000000 mask FFF000000 uncachable
[ 0.000000] 3 base 03CE00000 mask FFFE00000 uncachable
[ 0.000000] 4 base 03CE00000 mask FFFE00000 uncachable
[ 0.000000] 5 base 03CD00000 mask FFFF00000 uncachable
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] original variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 1GB, type WB
[ 0.000000] reg 1, base: 992MB, range: 32MB, type UC
[ 0.000000] reg 2, base: 976MB, range: 16MB, type UC
[ 0.000000] reg 3, base: 974MB, range: 2MB, type UC
[ 0.000000] reg 4, base: 974MB, range: 2MB, type UC
[ 0.000000] reg 5, base: 973MB, range: 1MB, type UC
[ 0.000000] total RAM covered: 973M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 64M num_reg: 5 lose cover RAM: 0G
[ 0.000000] New variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 1GB, type WB
[ 0.000000] reg 1, base: 973MB, range: 1MB, type UC
[ 0.000000] reg 2, base: 974MB, range: 2MB, type UC
[ 0.000000] reg 3, base: 976MB, range: 16MB, type UC
[ 0.000000] reg 4, base: 992MB, range: 32MB, type UC
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] BRK [0x031fe000, 0x031fefff] PGTABLE
[ 0.000000] BRK [0x031ff000, 0x031fffff] PGTABLE
[ 0.000000] BRK [0x03200000, 0x03200fff] PGTABLE
[ 0.000000] BRK [0x03201000, 0x03201fff] PGTABLE
[ 0.000000] BRK [0x03202000, 0x03202fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x33912000-0x35c80fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x000000003BDA6014 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x000000003BDA5100 0000DC (v01 ALASKA A M I 00000003 MSFT 0100000D)
[ 0.000000] ACPI: FACP 0x000000003BD9F000 00010C (v05 ALASKA A M I 00000003 AMI 0100000D)
[ 0.000000] ACPI: DSDT 0x000000003BD88000 0122CB (v02 ALASKA A M I 00000003 AMI 0100000D)
[ 0.000000] ACPI: TCPA 0x000000003BDA4000 000032 (v02 00000000 00000000)
[ 0.000000] ACPI: MSDM 0x000000003BDA3000 000055 (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: UEFI 0x000000003C31B000 000042 (v01 ALASKA A M I 00000000 00000000)
[ 0.000000] ACPI: BCFG 0x000000003BDA2000 0000BD (v01 ALASKA BATTCON 00000003 AMI 0100000D)
[ 0.000000] ACPI: OEM0 0x000000003BDA1000 000084 (v05 ALASKA BATTERY 00000003 AMI 0100000D)
[ 0.000000] ACPI: DBG2 0x000000003BDA0000 000072 (v00 ALASKA INTLDBG2 00000003 AMI 0100000D)
[ 0.000000] ACPI: HPET 0x000000003BD9E000 000038 (v01 ALASKA A M I 00000003 AMI 0100000D)
[ 0.000000] ACPI: LPIT 0x000000003BD9D000 000104 (v01 ALASKA A M I 00000003 AMI 0100000D)
[ 0.000000] ACPI: APIC 0x000000003BD9C000 00006C (v03 ALASKA A M I 00000003 AMI 0100000D)
[ 0.000000] ACPI: MCFG 0x000000003BD9B000 00003C (v01 ALASKA A M I 00000003 AMI 0100000D)
[ 0.000000] ACPI: SSDT 0x000000003BD87000 0005DA (v01 ALASKA CpuDptf 00000003 AMI 0100000D)
[ 0.000000] ACPI: SSDT 0x000000003BD84000 00249B (v01 ALASKA DptfTab 00000003 AMI 0100000D)
[ 0.000000] ACPI: SSDT 0x000000003BD83000 000058 (v01 ALASKA LowPwrM 00000003 AMI 0100000D)
[ 0.000000] ACPI: SSDT 0x000000003BD82000 0000FF (v01 ALASKA SoCDptf 00000003 AMI 0100000D)
[ 0.000000] ACPI: FPDT 0x000000003BD81000 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: SSDT 0x000000003BD80000 000763 (v01 PmRef CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x000000003BD7F000 000290 (v01 PmRef Cpu0Tst 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x000000003BD7E000 00017A (v01 PmRef ApTst 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x000000003BD7D000 000427 (v01 Intel_ Tpm2Tabl 00001000 INTL 20061109)
[ 0.000000] ACPI: TPM2 0x000000003BD7C000 000034 (v03 00000000 00000000)
[ 0.000000] ACPI: BGRT 0x000000003BD7B000 000038 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: CSRT 0x000000003BD7A000 00014C (v00 ALASKA A M I 00000005 INTL 20120624)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000003cbfffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x3bb6c000-0x3bb70fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x000000003cbfffff]
[ 0.000000] Normal empty
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000008efff]
[ 0.000000] node 0: [mem 0x0000000000090000-0x000000000009dfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x000000001fffffff]
[ 0.000000] node 0: [mem 0x0000000020200000-0x000000003bd3efff]
[ 0.000000] node 0: [mem 0x000000003c62b000-0x000000003cbfffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000003cbfffff]
[ 0.000000] On node 0 totalpages: 245936
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 22 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 3824 pages used for memmap
[ 0.000000] DMA32 zone: 241940 pages, LIFO batch:31
[ 0.000000] x86/hpet: Will disable the HPET for this platform because it's not reliable
[ 0.000000] Reserving Intel graphics stolen memory at 0x3cf00000-0x3eefffff
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-86
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x3bd3f000-0x3bd6efff]
[ 0.000000] PM: Registered nosave memory: [mem 0x3bd6f000-0x3bda6fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x3bda7000-0x3c366fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x3c367000-0x3c5d0fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x3c5d1000-0x3c62afff]
[ 0.000000] e820: [mem 0x3ef00000-0xe00f7fff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 33 pages/cpu @ffff88003b800000 s98008 r8192 d28968 u524288
[ 0.000000] pcpu-alloc: s98008 r8192 d28968 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 242026
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.4.0-21-generic.efi.signed root=UUID=d3cf0412-63bf-4f90-b32b-8797e9e37b26 ro nomodeset
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 868332K/983744K available (8356K kernel code, 1278K rwdata, 3920K rodata, 1476K init, 1292K bss, 115412K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:16640 nr_irqs:1024 0
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Maximum core-clock to bus-clock ratio: 0x10
[ 0.000000] Resolved frequency ID: 0, frequency: 83200 KHz
[ 0.000000] TSC runs at 1331200 KHz
[ 0.000000] lapic_timer_frequency = 332800
[ 0.000000] tsc: Detected 1331.200 MHz processor
[ 0.000058] Calibrating delay loop (skipped), value calculated using timer frequency.. 2662.40 BogoMIPS (lpj=5324800)
[ 0.000082] pid_max: default: 32768 minimum: 301
[ 0.000103] ACPI: Core revision 20150930
[ 0.062768] ACPI: 9 ACPI AML tables successfully acquired and loaded
[ 0.064576] Security Framework initialized
[ 0.064591] Yama: becoming mindful.
[ 0.064637] AppArmor: AppArmor initialized
[ 0.064907] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.065640] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.065993] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.066015] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.066527] Initializing cgroup subsys io
[ 0.066549] Initializing cgroup subsys memory
[ 0.066576] Initializing cgroup subsys devices
[ 0.066592] Initializing cgroup subsys freezer
[ 0.066607] Initializing cgroup subsys net_cls
[ 0.066622] Initializing cgroup subsys perf_event
[ 0.066638] Initializing cgroup subsys net_prio
[ 0.066652] Initializing cgroup subsys hugetlb
[ 0.066671] Initializing cgroup subsys pids
[ 0.066716] CPU: Physical Processor ID: 0
[ 0.066728] CPU: Processor Core ID: 0
[ 0.066742] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.066754] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.071669] mce: CPU supports 6 MCE banks
[ 0.071691] CPU0: Thermal monitoring enabled (TM1)
[ 0.071706] process: using mwait in idle threads
[ 0.071722] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[ 0.071734] Last level dTLB entries: 4KB 128, 2MB 16, 4MB 16, 1GB 0
[ 0.072272] Freeing SMP alternatives memory: 28K (ffffffff820b2000 - ffffffff820b9000)
[ 0.079681] ftrace: allocating 31878 entries in 125 pages
[ 0.107282] smpboot: Max logical packages: 1
[ 0.107301] smpboot: APIC(0) Converting physical 0 to logical package 0
[ 0.107378] TSC deadline timer enabled
[ 0.107385] smpboot: CPU0: Intel(R) Atom(TM) CPU Z3735G @ 1.33GHz (family: 0x6, model: 0x37, stepping: 0x8)
[ 0.107426] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, full-width counters, Intel PMU driver.
[ 0.107463] ... version: 3
[ 0.107473] ... bit width: 40
[ 0.107482] ... generic registers: 2
[ 0.107492] ... value mask: 000000ffffffffff
[ 0.107502] ... max period: 000000ffffffffff
[ 0.107512] ... fixed-purpose events: 3
[ 0.107522] ... event mask: 0000000700000003
[ 0.109677] x86: Booting SMP configuration:
[ 0.109693] .... node #0, CPUs: #1
[ 0.117007] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.117334] #2 #3
[ 0.131746] x86: Booted up 1 node, 4 CPUs
[ 0.131766] smpboot: Total of 4 processors activated (10649.60 BogoMIPS)
[ 0.133122] devtmpfs: initialized
[ 0.142380] evm: security.selinux
[ 0.142392] evm: security.SMACK64
[ 0.142402] evm: security.SMACK64EXEC
[ 0.142411] evm: security.SMACK64TRANSMUTE
[ 0.142420] evm: security.SMACK64MMAP
[ 0.142429] evm: security.ima
[ 0.142438] evm: security.capability
[ 0.142602] PM: Registering ACPI NVS region [mem 0x0008f000-0x0008ffff] (4096 bytes)
[ 0.142622] PM: Registering ACPI NVS region [mem 0x3bda7000-0x3c366fff] (6029312 bytes)
[ 0.143083] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.143319] pinctrl core: initialized pinctrl subsystem
[ 0.143600] RTC time: 11:49:32, date: 07/06/16
[ 0.143982] NET: Registered protocol family 16
[ 0.152840] cpuidle: using governor ladder
[ 0.164853] cpuidle: using governor menu
[ 0.164871] PCCT header not found.
[ 0.165045] ACPI: bus type PCI registered
[ 0.165058] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.165264] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.165286] PCI: not using MMCONFIG
[ 0.165297] PCI: Using configuration type 1 for base access
[ 0.181974] ACPI: Added _OSI(Module Device)
[ 0.181989] ACPI: Added _OSI(Processor Device)
[ 0.182001] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.182012] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.217161] ACPI: Dynamic OEM Table Load:
[ 0.217195] ACPI: SSDT 0xFFFF88003B1E9800 000501 (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
[ 0.219580] ACPI: Dynamic OEM Table Load:
[ 0.219608] ACPI: SSDT 0xFFFF88003B1EA000 000433 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.222636] ACPI: Dynamic OEM Table Load:
[ 0.222663] ACPI: SSDT 0xFFFF88003B266400 00015F (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.224994] ACPI: Dynamic OEM Table Load:
[ 0.225020] ACPI: SSDT 0xFFFF88003B1FD9C0 00008D (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.230084] ACPI: Interpreter enabled
[ 0.230112] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150930/hwxface-580)
[ 0.230141] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150930/hwxface-580)
[ 0.230167] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20150930/hwxface-580)
[ 0.230194] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S4_] (20150930/hwxface-580)
[ 0.230230] ACPI: (supports S0 S5)
[ 0.230241] ACPI: Using IOAPIC for interrupt routing
[ 0.230343] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.246851] [Firmware Info]: PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] not reserved in ACPI motherboard resources
[ 0.246873] PCI: not using MMCONFIG
[ 0.246889] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.253460] ACPI: Power Resource [USBC] (on)
[ 0.254379] ACPI: Power Resource [WWPR] (off)
[ 0.260756] ACPI: Power Resource [PLPE] (on)
[ 0.271114] ACPI: Power Resource [CLK0] (on)
[ 0.271261] ACPI: Power Resource [CLK1] (on)
[ 0.271581] ACPI: Power Resource [P28P] (off)
[ 0.271721] ACPI: Power Resource [P18P] (off)
[ 0.277092] ACPI: Power Resource [CLK0] (on)
[ 0.277237] ACPI: Power Resource [CLK1] (on)
[ 0.294599] ACPI: Power Resource [P28X] (off)
[ 0.294747] ACPI: Power Resource [P18X] (off)
[ 0.294898] ACPI: Power Resource [P28T] (off)
[ 0.295044] ACPI: Power Resource [P18T] (off)
[ 0.295182] ACPI: Power Resource [P1XT] (off)
[ 0.306560] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.306585] acpi PNP0A08:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[ 0.306725] \_SB_.PCI0:_OSC invalid UUID
[ 0.306730] _OSC request data:1 1e 0
[ 0.306742] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[ 0.306783] acpi PNP0A08:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[ 0.307747] PCI host bridge to bus 0000:00
[ 0.307764] pci_bus 0000:00: root bus resource [io 0x0070-0x0077]
[ 0.307779] pci_bus 0000:00: root bus resource [io 0x0000-0x006f window]
[ 0.307793] pci_bus 0000:00: root bus resource [io 0x0078-0x0cf7 window]
[ 0.307806] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.307820] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.307839] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.307857] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff window]
[ 0.307875] pci_bus 0000:00: root bus resource [mem 0x50c00000-0x50ffffff window]
[ 0.307894] pci_bus 0000:00: root bus resource [mem 0x3cf00001-0x3ef00000 window]
[ 0.307912] pci_bus 0000:00: root bus resource [mem 0x40000000-0x50affffe window]
[ 0.307930] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed40fff window]
[ 0.307949] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.307975] pci 0000:00:00.0: [8086:0f00] type 00 class 0x060000
[ 0.308249] pci 0000:00:02.0: [8086:0f31] type 00 class 0x030000
[ 0.308278] pci 0000:00:02.0: reg 0x10: [mem 0x50000000-0x503fffff]
[ 0.308296] pci 0000:00:02.0: reg 0x18: [mem 0x40000000-0x4fffffff pref]
[ 0.308313] pci 0000:00:02.0: reg 0x20: [io 0x1000-0x1007]
[ 0.308590] pci 0000:00:14.0: [8086:0f35] type 00 class 0x0c0330
[ 0.308627] pci 0000:00:14.0: reg 0x10: [mem 0x50a00000-0x50a0ffff 64bit]
[ 0.308698] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.308938] pci 0000:00:16.0: [8086:0f37] type 00 class 0x0c0380
[ 0.308966] pci 0000:00:16.0: reg 0x10: [mem 0x50400000-0x505fffff]
[ 0.308980] pci 0000:00:16.0: reg 0x14: [mem 0x50a2c000-0x50a2cfff]
[ 0.309048] pci 0000:00:16.0: PME# supported from D0 D3hot
[ 0.309378] pci 0000:00:1a.0: [8086:0f18] type 00 class 0x108000
[ 0.309429] pci 0000:00:1a.0: reg 0x10: [mem 0x50900000-0x509fffff]
[ 0.309448] pci 0000:00:1a.0: reg 0x14: [mem 0x50800000-0x508fffff]
[ 0.309558] pci 0000:00:1a.0: PME# supported from D0 D3hot
[ 0.309802] pci 0000:00:1f.0: [8086:0f1c] type 00 class 0x060100
[ 0.311111] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.311335] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.311554] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.311774] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.311993] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.312214] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.312438] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.312670] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.329339] vgaarb: setting as boot device: PCI:0000:00:02.0
[ 0.329358] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.329378] vgaarb: loaded
[ 0.329387] vgaarb: bridge control possible 0000:00:02.0
[ 0.330133] SCSI subsystem initialized
[ 0.330276] libata version 3.00 loaded.
[ 0.330360] ACPI: bus type USB registered
[ 0.330424] usbcore: registered new interface driver usbfs
[ 0.330462] usbcore: registered new interface driver hub
[ 0.330529] usbcore: registered new device driver usb
[ 0.331098] PCI: Using ACPI for IRQ routing
[ 0.331113] PCI: pci_cache_line_size set to 64 bytes
[ 0.331145] Expanded resource reserved due to conflict with PCI Bus 0000:00
[ 0.331160] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
[ 0.331165] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[ 0.331170] e820: reserve RAM buffer [mem 0x3bd3f000-0x3bffffff]
[ 0.331174] e820: reserve RAM buffer [mem 0x3cc00000-0x3fffffff]
[ 0.331493] NetLabel: Initializing
[ 0.331505] NetLabel: domain hash size = 128
[ 0.331515] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.331552] NetLabel: unlabeled traffic allowed by default
[ 0.331790] clocksource: Switched to clocksource refined-jiffies
[ 0.349517] AppArmor: AppArmor Filesystem Enabled
[ 0.349737] pnp: PnP ACPI init
[ 0.349902] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.350250] system 00:01: [io 0x0680-0x069f] has been reserved
[ 0.350267] system 00:01: [io 0x0400-0x047f] has been reserved
[ 0.350282] system 00:01: [io 0x0500-0x05fe] has been reserved
[ 0.350295] system 00:01: [io 0x0600-0x061f] has been reserved
[ 0.350310] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.350328] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.350614] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.356647] pnp: PnP ACPI: found 3 devices
[ 0.362678] pci_bus 0000:00: resource 4 [io 0x0070-0x0077]
[ 0.362687] pci_bus 0000:00: resource 5 [io 0x0000-0x006f window]
[ 0.362694] pci_bus 0000:00: resource 6 [io 0x0078-0x0cf7 window]
[ 0.362700] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.362706] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.362713] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.362719] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000fffff window]
[ 0.362725] pci_bus 0000:00: resource 11 [mem 0x50c00000-0x50ffffff window]
[ 0.362731] pci_bus 0000:00: resource 12 [mem 0x3cf00001-0x3ef00000 window]
[ 0.362738] pci_bus 0000:00: resource 13 [mem 0x40000000-0x50affffe window]
[ 0.362744] pci_bus 0000:00: resource 14 [mem 0xfed40000-0xfed40fff window]
[ 0.362829] NET: Registered protocol family 2
[ 0.363242] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.363314] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 0.363384] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.363469] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.363497] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.363616] NET: Registered protocol family 1
[ 0.363669] pci 0000:00:02.0: Video device with shadowed ROM
[ 0.363737] PCI: CLS 0 bytes, default 64
[ 0.363877] Trying to unpack rootfs image as initramfs...
[ 1.834163] Freeing initrd memory: 36284K (ffff880033912000 - ffff880035c81000)
[ 1.834573] Scanning for low memory corruption every 60 seconds
[ 1.835706] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 1.835793] audit: initializing netlink subsys (disabled)
[ 1.835846] audit: type=2000 audit(1467805773.740:1): initialized
[ 1.836794] Initialise system trusted keyring
[ 1.837078] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.841997] zbud: loaded
[ 1.842531] VFS: Disk quotas dquot_6.6.0
[ 1.842649] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.844218] fuse init (API version 7.23)
[ 1.844632] Key type big_key registered
[ 1.845589] Key type asymmetric registered
[ 1.845606] Asymmetric key parser 'x509' registered
[ 1.845727] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.845838] io scheduler noop registered
[ 1.845854] io scheduler deadline registered (default)
[ 1.845961] io scheduler cfq registered
[ 1.846289] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.846319] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.846441] efifb: probing for efifb
[ 1.846482] efifb: framebuffer at 0x40000000, mapped to 0xffffc90000400000, using 2432k, total 2432k
[ 1.846501] efifb: mode is 1024x600x32, linelength=4096, pages=1
[ 1.846511] efifb: scrolling: redraw
[ 1.846523] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.852459] Console: switching to colour frame buffer device 128x37
[ 1.858169] fb0: EFI VGA frame buffer device
[ 1.858261] intel_idle: MWAIT substates: 0x33000020
[ 1.858267] intel_idle: v0.4.1 model 0x37
[ 1.858270] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.858987] ACPI: AC Adapter [ADP1] (off-line)
[ 1.863934] [Firmware Bug]: No valid trip found
[ 1.864167] GHES: HEST is not enabled!
[ 1.864520] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.884776] 00:02: ttyS0 at I/O 0x3f8 (irq = 199, base_baud = 115200) is a 16550A
[ 1.889442] hpet: number irqs doesn't agree with number of timers
[ 1.889711] Linux agpgart interface v0.103
[ 1.898206] brd: module loaded
[ 1.901921] loop: module loaded
[ 1.902640] libphy: Fixed MDIO Bus: probed
[ 1.902716] tun: Universal TUN/TAP device driver, 1.6
[ 1.905000] tun: (C) 1999-2004 Max Krasnyansky
[ 1.907437] PPP generic driver version 2.4.2
[ 1.909895] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.912237] ehci-pci: EHCI PCI platform driver
[ 1.914548] ehci-platform: EHCI generic platform driver
[ 1.916917] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.919236] ohci-pci: OHCI PCI platform driver
[ 1.921546] ohci-platform: OHCI generic platform driver
[ 1.923869] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.926543] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.928898] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 1.932368] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
[ 1.934721] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 1.935046] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.937442] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.939844] usb usb1: Product: xHCI Host Controller
[ 1.942247] usb usb1: Manufacturer: Linux 4.4.0-21-generic xhci-hcd
[ 1.944663] usb usb1: SerialNumber: 0000:00:14.0
[ 1.947529] hub 1-0:1.0: USB hub found
[ 1.949897] hub 1-0:1.0: 6 ports detected
[ 2.455926] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 2.458558] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 2.460988] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.463317] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.465661] usb usb2: Product: xHCI Host Controller
[ 2.467966] usb usb2: Manufacturer: Linux 4.4.0-21-generic xhci-hcd
[ 2.470286] usb usb2: SerialNumber: 0000:00:14.0
[ 2.473107] hub 2-0:1.0: USB hub found
[ 2.475429] hub 2-0:1.0: 1 port detected
[ 2.478166] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 2.801057] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x13303f810e3, max_idle_ns: 440795235405 ns
[ 3.515098] i8042: No controller found
[ 3.517481] clocksource: Switched to clocksource tsc
[ 3.517823] mousedev: PS/2 mouse device common for all mice
[ 3.518122] ACPI Warning: Could not enable fixed event - RealTimeClock (4) (20150930/evxface-654)
[ 3.518565] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0
[ 3.518606] rtc_cmos 00:00: alarms up to one day, 242 bytes nvram
[ 3.518629] i2c /dev entries driver
[ 3.518829] device-mapper: uevent: version 1.0.3
[ 3.519250] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 3.519277] Intel P-state driver initializing.
[ 3.520286] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.520303] EFI Variables Facility v0.08 2004-May-17
[ 3.531625] NET: Registered protocol family 10
[ 3.532798] NET: Registered protocol family 17
[ 3.532864] Key type dns_resolver registered
[ 3.534348] microcode: CPU0 sig=0x30678, pf=0x2, revision=0x82a
[ 3.534422] microcode: CPU1 sig=0x30678, pf=0x2, revision=0x82a
[ 3.534553] microcode: CPU2 sig=0x30678, pf=0x2, revision=0x82a
[ 3.534561] microcode: CPU3 sig=0x30678, pf=0x2, revision=0x82a
[ 3.534847] microcode: Microcode Update Driver: v2.01 , Peter Oruba
[ 3.535939] registered taskstats version 1
[ 3.535968] Loading compiled-in X.509 certificates
[ 3.538028] Loaded X.509 cert 'Build time autogenerated kernel key: fc7c0e9f152f32eca50ea2d9722926e5127af244'
[ 3.538068] zswap: loaded using pool lzo/zbud
[ 3.543386] Key type trusted registered
[ 3.554914] Key type encrypted registered
[ 3.554930] AppArmor: AppArmor sha1 policy hashing enabled
[ 3.554936] ima: No TPM chip found, activating TPM-bypass!
[ 3.554984] evm: HMAC attrs: 0x1
[ 3.555638] Magic number: 8:409:832
[ 3.557152] rtc_cmos 00:00: setting system clock to 2016-07-06 11:49:35 UTC (1467805775)
[ 3.557693] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 3.557694] EDD information not available.
[ 3.557976] PM: Hibernation image not present or could not be loaded.
[ 3.586345] Freeing unused kernel memory: 1476K (ffffffff81f41000 - ffffffff820b2000)
[ 3.588244] Write protecting the kernel read-only data: 14336k
[ 3.593362] Freeing unused kernel memory: 1872K (ffff88000282c000 - ffff880002a00000)
[ 3.597004] Freeing unused kernel memory: 176K (ffff880002dd4000 - ffff880002e00000)
[ 3.683995] random: systemd-udevd urandom read with 2 bits of entropy available
[ 3.729789] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[ 3.775111] sdhci: Secure Digital Host Controller Interface driver
[ 3.777201] sdhci: Copyright(c) Pierre Ossman
[ 3.783937] sdhci-acpi 80860F14:00: No vmmc regulator found
[ 3.786066] sdhci-acpi 80860F14:00: No vqmmc regulator found
[ 3.791443] mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
[ 3.793954] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.794813] sdhci-acpi INT33BB:00: No vmmc regulator found
[ 3.794816] sdhci-acpi INT33BB:00: No vqmmc regulator found
[ 3.798065] mmc1: SDHCI controller on ACPI [INT33BB:00] using ADMA
[ 3.799439] sdhci-acpi 80860F14:02: No vmmc regulator found
[ 3.799441] sdhci-acpi 80860F14:02: No vqmmc regulator found
[ 3.802853] mmc2: SDHCI controller on ACPI [80860F14:02] using ADMA
[ 3.831738] FUJITSU Extended Socket Network Device Driver - version 1.0 - Copyright (c) 2015 FUJITSU LIMITED
[ 3.867699] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 3.871190] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.873451] usb 1-1: Product: USB2.0 Hub
[ 3.876408] hub 1-1:1.0: USB hub found
[ 3.879797] hub 1-1:1.0: 4 ports detected
[ 3.887845] [drm] Initialized drm 1.1.0 20060810
[ 3.939535] mmc0: MAN_BKOPS_EN bit is not set
[ 3.951181] mmc0: new HS200 MMC card at address 0001
[ 3.974280] mmcblk0: mmc0:0001 016G70 14.7 GiB
[ 3.976944] mmcblk0boot0: mmc0:0001 016G70 partition 1 4.00 MiB
[ 3.979259] mmcblk0boot1: mmc0:0001 016G70 partition 2 4.00 MiB
[ 3.981511] mmcblk0rpmb: mmc0:0001 016G70 partition 3 4.00 MiB
[ 3.989839] mmcblk0: p1 p2 p3
[ 4.028886] mmc1: new high speed SDIO card at address 0001
[ 4.162060] usb 1-1.1: new low-speed USB device number 3 using xhci_hcd
[ 4.282213] usb 1-1.1: New USB device found, idVendor=04d9, idProduct=1503
[ 4.284964] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.286683] usb 1-1.1: Product: USB Keyboard
[ 4.288343] usb 1-1.1: Manufacturer:
[ 4.290440] usb 1-1.1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 4.292183] usb 1-1.1: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 4.330748] usbcore: registered new interface driver usbhid
[ 4.333678] usbhid: USB HID core driver
[ 4.340173] input: USB Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.1/1-1.1:1.0/0003:04D9:1503.0001/input/input0
[ 4.370061] usb 1-1.2: new high-speed USB device number 4 using xhci_hcd
[ 4.399550] hid-generic 0003:04D9:1503.0001: input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:14.0-1.1/input0
[ 4.408461] input: USB Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.1/1-1.1:1.1/0003:04D9:1503.0002/input/input1
[ 4.467507] hid-generic 0003:04D9:1503.0002: input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:14.0-1.1/input1
[ 4.546159] usb 1-1.2: New USB device found, idVendor=058f, idProduct=6387
[ 4.549516] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.551705] usb 1-1.2: Product: Mass Storage Device
[ 4.553883] usb 1-1.2: Manufacturer: JetFlash
[ 4.555984] usb 1-1.2: SerialNumber: LCM97Z3I
[ 4.569100] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 4.573089] scsi host0: usb-storage 1-1.2:1.0
[ 4.575429] usbcore: registered new interface driver usb-storage
[ 4.582580] usbcore: registered new interface driver uas
[ 4.634060] usb 1-1.3: new high-speed USB device number 5 using xhci_hcd
[ 4.730982] usb 1-1.3: New USB device found, idVendor=056e, idProduct=4008
[ 4.734272] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.736398] usb 1-1.3: Product: WDC-150SU2M
[ 4.738515] usb 1-1.3: Manufacturer: ELECOM

[ 4.814062] usb 1-1.4: new low-speed USB device number 6 using xhci_hcd
[ 4.912727] usb 1-1.4: New USB device found, idVendor=0101, idProduct=0007
[ 4.916777] usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.918948] usb 1-1.4: Product: USB OPTICAL MOUSE
[ 4.921452] usb 1-1.4: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 4.930073] input: USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:0101:0007.0003/input/input2
[ 4.936479] hid-generic 0003:0101:0007.0003: input,hidraw2: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0000:00:14.0-1.4/input0
[ 5.571974] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 5.576350] scsi 0:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2
[ 5.580555] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.584940] sd 0:0:0:0: [sda] 3944448 512-byte logical blocks: (2.02 GB/1.88 GiB)
[ 5.587747] sd 0:0:0:0: [sda] Write Protect is off
[ 5.589991] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 5.590593] sd 0:0:0:0: [sda] No Caching mode page found
[ 5.590596] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 5.799989] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 5.805783] systemd[1]: Detected architecture x86-64.
[ 5.818424] systemd[1]: Set hostname to .
[ 5.965935] sda: sda1
[ 5.970003] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 5.993738] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 5.998883] systemd[1]: Reached target Remote File Systems (Pre).
[ 6.003800] systemd[1]: Reached target Remote File Systems.
[ 6.008703] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 6.013463] systemd[1]: Listening on Journal Socket (/dev/log).
[ 6.018088] systemd[1]: Listening on udev Control Socket.
[ 6.022676] systemd[1]: Reached target Encrypted Volumes.
[ 6.027222] systemd[1]: Reached target User and Group Name Lookups.
[ 6.032085] systemd[1]: Created slice System Slice.
[ 6.036828] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 6.041515] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 6.046142] systemd[1]: Listening on Journal Socket.
[ 6.062578] systemd[1]: Starting Braille Device Support...
[ 6.069984] systemd[1]: Mounting Debug File System...
[ 6.077005] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 6.084141] systemd[1]: Mounting POSIX Message Queue File System...
[ 6.091081] systemd[1]: Started Read required files in advance.
[ 6.097051] systemd[1]: Listening on udev Kernel Socket.
[ 6.102672] systemd[1]: Listening on Journal Audit Socket.
[ 6.107670] systemd[1]: Created slice User and Session Slice.
[ 6.115160] systemd[1]: Starting Load Kernel Modules...
[ 6.120872] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 6.126061] systemd[1]: Listening on Syslog Socket.
[ 6.132297] systemd[1]: Starting Journal Service...
[ 6.139250] systemd[1]: Starting Uncomplicated firewall...
[ 6.145041] systemd[1]: Listening on LVM2 poll daemon socket.
[ 6.150379] systemd[1]: Reached target Slices.
[ 6.155862] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 6.168338] lp: driver loaded but no devices found
[ 6.178268] ppdev: user-space parallel port driver
[ 6.181487] systemd[1]: Mounting Huge Pages File System...
[ 6.186918] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 6.193702] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[ 6.199698] systemd[1]: Created slice system-getty.slice.
[ 6.209953] systemd[1]: Mounted Debug File System.
[ 6.215325] systemd[1]: Mounted Huge Pages File System.
[ 6.220523] systemd[1]: Mounted POSIX Message Queue File System.
[ 6.227134] systemd[1]: Started Braille Device Support.
[ 6.233220] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 6.239461] systemd[1]: Started Load Kernel Modules.
[ 6.245598] systemd[1]: Started Uncomplicated firewall.
[ 6.251731] systemd[1]: Started Journal Service.
[ 6.613612] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ 6.697507] systemd-journald[316]: Received request to flush runtime journal from PID 1
[ 6.835295] 80860F0A:00: ttyS4 at MMIO 0x50b47000 (irq = 191, base_baud = 2764800) is a 16550A
[ 6.837216] 80860F0A:01: ttyS5 at MMIO 0x50b4d000 (irq = 192, base_baud = 2764800) is a 16550A
[ 6.913238] dw_dmac INTL9C60:00: DesignWare DMA Controller, 8 channels
[ 6.916622] Bluetooth: Core ver 2.21
[ 6.916658] NET: Registered protocol family 31
[ 6.916663] Bluetooth: HCI device and connection manager initialized
[ 6.916672] Bluetooth: HCI socket layer initialized
[ 6.916679] Bluetooth: L2CAP socket layer initialized
[ 6.916695] Bluetooth: SCO socket layer initialized
[ 6.918468] dw_dmac INTL9C60:01: DesignWare DMA Controller, 8 channels
[ 6.941257] Bluetooth: HCI UART driver ver 2.3
[ 6.941265] Bluetooth: HCI UART protocol H4 registered
[ 6.941321] Bluetooth: HCI UART protocol BCSP registered
[ 6.941325] Bluetooth: HCI UART protocol LL registered
[ 6.941328] Bluetooth: HCI UART protocol ATH3K registered
[ 6.941331] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 6.943843] Bluetooth: HCI UART protocol Intel registered
[ 6.943902] Bluetooth: HCI UART protocol BCM registered
[ 6.943907] Bluetooth: HCI UART protocol QCA registered
[ 6.951693] i2c_designware 80860F41:04: I2C bus managed by PUNIT
[ 6.972095] axp20x i2c-INT33F4:00: AXP20x variant AXP288 found
[ 7.023451] mei_txe 0000:00:1a.0: can't derive routing for PCI INT A
[ 7.023460] mei_txe 0000:00:1a.0: PCI INT A: no GSI
[ 7.193966] axp20x i2c-INT33F4:00: AXP20X driver loaded
[ 7.197154] ACPI: Battery Slot [BMBT] (battery present)
[ 7.197417] [Firmware Bug]: No valid trip found
[ 7.224804] random: nonblocking pool is initialized
[ 7.341149] SSE version of gcm_enc/dec engaged.
[ 7.341698] Adding 983036k swap on /dev/mmcblk0p3. Priority:-1 extents:1 across:983036k SSFS
[ 7.516846] byt-rt5640 byt-rt5640: ASoC: CPU DAI baytrail-pcm-audio not registered
[ 7.521951] byt-rt5640 byt-rt5640: ASoC: CPU DAI baytrail-pcm-audio not registered
[ 7.566945] intel_rapl: Found RAPL domain package
[ 7.566955] intel_rapl: Found RAPL domain core
[ 7.594831] genirq: Flags mismatch irq 8. 00000083 (volume_down) vs. 00000000 (rtc0)
[ 7.596836] gpio-keys gpio-keys.0.auto: Unable to claim irq 8; error -16
[ 7.608970] gpio-keys: probe of gpio-keys.0.auto failed with error -16
[ 7.609245] input: gpio-keys as /devices/platform/gpio-keys.1.auto/input/input4
[ 7.611191] byt-rt5640 byt-rt5640: ASoC: CPU DAI baytrail-pcm-audio not registered
[ 7.643831] dwc3 dwc3.2.auto: failed to register ULPI interface
[ 7.648749] dwc3: probe of dwc3.2.auto failed with error -110
[ 7.660685] byt-rt5640 byt-rt5640: ASoC: CPU DAI baytrail-pcm-audio not registered
[ 7.861301] baytrail-pcm-audio baytrail-pcm-audio: ipc: error DSP boot timeout
[ 7.977531] input: axp20x-pek as /devices/platform/80860F41:04/i2c-4/i2c-INT33F4:00/axp20x-pek/input/input5
[ 7.978575] byt-rt5640 byt-rt5640: ASoC: CPU DAI baytrail-pcm-audio not registered
[ 8.025582] audit: type=1400 audit(1467805779.968:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/ubuntu-core-launcher" pid=632 comm="apparmor_parser"
[ 8.033124] audit: type=1400 audit(1467805779.972:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=629 comm="apparmor_parser"
[ 8.033148] audit: type=1400 audit(1467805779.972:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=629 comm="apparmor_parser"
[ 8.033164] audit: type=1400 audit(1467805779.972:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=629 comm="apparmor_parser"
[ 8.033178] audit: type=1400 audit(1467805779.972:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=629 comm="apparmor_parser"
[ 8.033522] audit: type=1400 audit(1467805779.976:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=628 comm="apparmor_parser"
[ 8.033548] audit: type=1400 audit(1467805779.976:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session//chromium" pid=628 comm="apparmor_parser"
[ 8.037995] audit: type=1400 audit(1467805779.980:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=634 comm="apparmor_parser"
[ 8.042807] audit: type=1400 audit(1467805779.984:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="webbrowser-app" pid=633 comm="apparmor_parser"
[ 8.042831] audit: type=1400 audit(1467805779.984:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="webbrowser-app//oxide_helper" pid=633 comm="apparmor_parser"
[ 8.208424] r8188eu: module is from the staging directory, the quality is unknown, you have been warned.
[ 8.215859] Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)
[ 8.272651] usbcore: registered new interface driver r8188eu
[ 8.272715] byt-rt5640 byt-rt5640: ASoC: CPU DAI baytrail-pcm-audio not registered
[ 8.285679] r8188eu 1-1.3:1.0 wlx0090fec6d71a: renamed from wlan0
[ 8.417062] cfg80211: World regulatory domain updated:
[ 8.417072] cfg80211: DFS Master region: unset
[ 8.417075] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.417082] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.417086] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.417091] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.417096] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 8.417101] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 8.417105] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 8.417110] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.417114] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 8.879740] IPv6: ADDRCONF(NETDEV_UP): wlx0090fec6d71a: link is not ready
[ 9.254151] MAC Address = 00:90:fe:c6:d7:1a
[ 9.256357] IPv6: ADDRCONF(NETDEV_UP): wlx0090fec6d71a: link is not ready
[ 9.489822] IPv6: ADDRCONF(NETDEV_UP): wlx0090fec6d71a: link is not ready
[ 12.283066] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 12.283075] Bluetooth: BNEP filters: protocol multicast
[ 12.283085] Bluetooth: BNEP socket layer initialized
[ 14.222130] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 14.564366] R8188EU: ERROR assoc success
[ 14.564506] IPv6: ADDRCONF(NETDEV_CHANGE): wlx0090fec6d71a: link becomes ready
posted by kapper at 00:43 | Comment(0) | Ubuntu
この記事へのコメント
コメントを書く
お名前:

メールアドレス:

ホームページアドレス:

コメント:

にほんブログ村 IT技術ブログへ
にほんブログ村

Linux ブログランキングへ